Screw Fasting Counter – nitto-kohki.vn

DLR5340-WE Non-CE

nittoadmin — Thu, 27 Feb 2020 05:53:26 +0000

- Three dedicated screwdrivers can be connected.
- Eight kinds of screw fastening conditions can be stored in internal

Model                           : DLR5340-WE
Count                           : 0 - 99
Counting Method                 : Count-up / Count-down
Count Correction Function       : Count normal fastening only
Self Adjustment Timer Setting   : 0.01 to 2.50 sec.
Work Detection Function         : Yes (1 terminal) / No
Work Installation Timer Setting : 0 to 9.5 sec.
OK Outout Timer Setting         : 0 to 9.5 sec.
NG Alarm                   : ON(1)/ ON(2)/ OFF
OK Buzzer                  : ON(1)/ ON(2)/ ON(3)/ ON(4)/ ON(5)/ OFF
Count Return Function           : ON / OFF
Screwdriver Lock Function       : ON / OFF
Screwdriver Cord Connection     : Single cord connection
(Single and power lines)
External Input on Terminal Block
: SENSOR / RESET / TORQUE CHECK / ch1/2/3
External Outputs on Terminal Block
: OK / NG / COUNT-UP / DRIVER A/B/C
Input Voltage                   : 100-240 V AC, 50/60 Hz
ExternalDimensions   (mm[inch])
: W150 x D120 x H60 [W5.91" x D4.72" x H2.36"]
Mass            (g[lbs]) : 620[1.37]
Accessories               : 2 m Power Cord with UL three-prong plug.
This product is for use outside Japan.

Bài viết DLR5340-WE Non-CE đã xuất hiện đầu tiên vào ngày nitto-kohki.vn.

DLR5040A-WE Non-CE

nittoadmin — Thu, 27 Feb 2020 05:53:26 +0000

For prevention of human fastening errors and enhanced fastening management accuracy
- Ideally suited for the assembly lines of vehicles and electrical equipment requiring reliable screw fastening
- The controller receives signals from electric screwdrivers to provide highly reliable screw fastening control
- Count Return Function: When a screw is loosened, a reverse signal output from the electric screwdriver reverses the count by one
- The Count Correction Function does not count elevated screws or double fastening
- Input voltage range from 100 to 240 V AC is acceptable in any part of the world
(The screwdrivers to be used in combination with the counter require input power supplies that are written on the respective nameplate)
- Link Connection Function: You can build up a simple sequential screw tightening system by connecting the DLR5040A-WE screw tightening counters in series without using any external controller such as a programmable controller
- Driver Lock Function prevents unexpected start of screwdrivers
- Compact and Lightweight (Compared with our conventional models decreased by 30 % in volume and by 38 % in mass)
- SPC type screwdrivers for DLR5040A-WE are designed on the basis of established transformerless screwdrivers

Model                           : DLR5040A-WN
Count                           : 1 - 99
Counting Method                 : Count-up / Count-down
Count Correction Function       : Count normal fastening only
Self Adjustment Timer Setting   : 0.01 to 0.99 sec.
Work Detection Function         : Yes (1 terminal) / No
External Count Input            : 2 terminals (PARTS A / PARTS B)
Work Installation Timer Setting : 0 to 9.5 sec.
OK Outout Timer Setting         : 0 to 9.5 sec.
NG Alarm                        : ON(1) / ON(2) / OFF
OK Buzzer                       : ON(1) / ON(2) / ON(3) / OFF
Count Return Function           : ON / OFF
NG Judge Timing                 : WORK SET / DRIVER ON
Automatic / Manual OK Judge     : AUTO / MANUAL
Screwdriver Lock Function       : ON / OFF
Multiple Link                   : Up to 10 counters can be connected.
External Input on Terminal Block
: SENSOR / RESET / LINK-IN / PARTS A / PARTS B
External Output on Terminal Block : OK / NG / LINK-OUT
Parameter Memory
: Parameters stored in internal nonvolatile memory
Input Voltage                   : 100-240 V AC, 50/60 Hz
External Dimensions  (mm[inch])
: W100 x D120 x H60 [W3.94" x D4.72" x H2.36"]
Mass                   (g[lbs]) : 470[1.04]
Accessories                     : 2 m Cord with UL three-prong plug.
This product is for use outside Japan.

Bài viết DLR5040A-WE Non-CE đã xuất hiện đầu tiên vào ngày nitto-kohki.vn.

DLR5640-WN Non-CE

nittoadmin — Thu, 27 Feb 2020 05:53:26 +0000

- Functions of the controller and counter are integrated into a single unit.
- Equipped with Linear Start Function that gradually increases the rotation speed at start.
- Input Voltage range from 100V AC to 240V AC is acceptable in any part of the world.

Model                           : DLR5640-WN
Count                           : 1 - 99
Counting Method                 : Count-up / Count-down
Count Correction Function       : Count normal fastening only
Self Adjustment Timer Setting   : 0.01 to 0.99 sec.
Work Detection Function         : Yes (1 terminal) / No
External Count Input            : 2 terminals (PARTS A / PARTS B)
Work Installation Timer Setting : 0 to 9.5 sec.
OK Outout Timer Setting         : 0 to 9.5 sec.
NG Alarm                        : ON(1) / ON(2) / OFF
OK Buzzer                       : ON(1) / ON(2) / ON(3) / OFF
Count Return Function           : ON / OFF
NG Judge Timing                 : WORK SET / DRIVER ON
Automatic / Manual OK Judge     : AUTO / MANUAL
Screwdriver Lock Function       : ON / OFF
Multiple Link                   : Up to 10 counters can be connected.
External Input on Terminal Block
: SENSOR / RESET / LINK-IN / PARTS A / PARTS B
External Output on Terminal Block : OK / NG / LINK-OUT
Parameter Memory
: Parameters stored in internal nonvolatile memory
Screwdriver Control             : SPEED / LINEAR START
Input Voltage                   : 100-240 V AC, 50/60 Hz
Screwdriver Power Supply        : 33 V DC, 1.5 A
External Dimensions  (mm[inch])
: W101 x D140 x H57 [W3.98" x D5.51" x H2.24"]
Mass                   (g[lbs]) : 800[1.76]
Accessories                     : 2 m Power Cord with USA plug
Suspension bail (2 pcs.)

Bài viết DLR5640-WN Non-CE đã xuất hiện đầu tiên vào ngày nitto-kohki.vn.

Counter DLR70S-WGB 100-240V Europe Plug

nittoadmin — Thu, 27 Feb 2020 05:53:26 +0000

- Equipped with "Stepless Speed Adjustment" function and "Soft Start" function.
- "Count Correction" function does not count fastening errors such as elevated screws or double fastening.
- "Count Back (Count Return)" function: When a screw is loosened, a reverse signal output from the electric screwdriver reverses the count by one.
- Up to four different screw fastening settings can be saved in the internal memory for a wide variety of assembly work.
- "Link Connection" function: Up to 10 screwdriver/controller sets can be connected in series.

Model :DLR70S-WGB
Input Voltage :100 - 240 V AC, 50/60Hz
Output Voltage :40 V DC
Speed Control Function :60 to 100 %
Soft Start Function :0 to 2 sec.
Count :0 to 99
Allowable Number of Screw Fastening Programs:4
Counting Method :Count-up / Count-down
Count Correction Function :Count normal fastening only
Self Adjustable Timer Setting :0.01 to 0.99 sec.
OK Output Timer Setting :0 to 9.5 sec.
Count Back Function :ON / OFF
OK / NG Buzzer :ON / OFF
Input Signal :WORK / RESET / LINK-IN /
CH1 / CH2 / TORQUE CHECK
Output Signal :OK / NG / LINK-OUT / TORQUE UP
Mass (g [Ibs]):2100 [4.63]
Size W x L x H (mm):117 x 325 x 76
([inch]):[4.61" x 12.80" x 2.99"]
Bit Grounding :Ready (With a 1M ohm resistor)
Plug shape :Europe
Standard Accessories :Power cord (2 m): 1
Fuse (5 A): 1

Applicable Screwdriver
- DLV30A/45A/70A-ASK

Bài viết Counter DLR70S-WGB 100-240V Europe Plug đã xuất hiện đầu tiên vào ngày nitto-kohki.vn.

DLR1510-JE 230V for DLV7500/8500 Series

nittoadmin — Thu, 27 Feb 2020 05:53:26 +0000

Model             : DLR1510-JE
Function
: Screw counting : OK lamp and buzzer for notification
Variable non-operation time
Setting protection by key lock switch
Setting by touch switch for easy operation
External output signals : Start, Torque up, Count up & Cycle OK
Input Voltage     : 230V AC, 50/60 Hz
Plug Shape        : Europe
Mass     (g[lbs]) : 5100[11.24]

Applicable Screwdriver
- DLV7500/8500 Series

Bài viết DLR1510-JE 230V for DLV7500/8500 Series đã xuất hiện đầu tiên vào ngày nitto-kohki.vn.